Brands

The BYD Battery-Box Premium HVS and HVM are modular high voltage lithium iron phosphate (LFP) battery packs for use with an external inverter.

The BYD Battery-Box Premium LVL is a high capacity 48V lithium iron phosphate (LFP) battery for use with an external inverter.

The BYD Battery-Box Premium LVS is a modular 48V lithium iron phosphate (LFP) battery pack for use with an external inverter.

Used on GSE In-Roof systems as an alternative to Rooflex sealing strip.

The speciality flashing for solar PV cables on tile or slate roofs

The SolarDek™ HookFlash provides a low-cost weather sealing solution for on-roof solar when roof hooks are flashed on slate, concrete or flat profile tiles.

Double pole circuit breakers. These protect the DC cables between batteries and inverters against overcurrent and short-circuit and allow easy isolation for installation or maintenance of the inverters.

An automatic transfer switch, suitable for the SMA 'Flexible Storage System' which allows operation to continue in case of main power blackouts. Contactors ensure compliant earth switching.

GSE Integration mid and end clamps for fixing the panels to the polypropylene mounting plate.

GSE Integration mounting screws for fixing the polypropylene module mounts to the battens.

GSE Integration Portrait Roof Mounts

Cost effective switches with a simple easy to install design.

Three and four pole (for three phase) single throw switches lockable in the off position only, mounted in enclosure. Rated: 230/400 Vac.

Changeover switch to enable Fronius GEN24 full backup functionality.

These fluorescent lights are perfect for efficient lighting both for external use and in high humidity conditions (IP65 rated). Tough GRP casing with rubber seal and clear polycarbonate lens held in place by clamps to provide a watertight seal.

The Superlux uses two high power Cree LEDs that are run at 700 mA which offers a light level of more than 340 lumens. The low profile design allows for quick and easy surface mounting without causing any obstruction.

This light utilises 6 x 2.5W Power LED’s to create a powerful arc of light and has an IP67 rating offering maximum protection.With a power draw of up to 50% less than standard halogen products and rated life of 60,000 hours.

The Leading Edge LE-300 wind turbine, efficient, compact, quiet and considered to be the most rugged and reliable horizontal axis wind turbine in its class.

Rating: 160 watts @ 8m/s (17.8mph) wind
Peak output: 750 watts @ 18m/s (40mph)
Voltage: 12, 24 or 48 volts DC.
Rotor Diameter: 1.54m
Cut In Windspeed: 3m/s (6.7mph)

This is a complete guyed tower assembly for the LE-300, LE-450 & LE-600 that is quick and easy to install with a minimal tool requirements.

Kits to permanently join, seal and insulate pump cables.

Mechanically activated device for water level detection in applications with LORENTZ Solar Pump Systems. The switch can be used to detect the water level within a tank. When the water level in the tank reaches the maximum, the LORENTZ Controller will stop the pump and indicate Tank Full.

These protect your Lorentz pump system from lightning strikes.

Rating: 404 W in a 11 m/s (24.6 mph) wind.
Voltage: 12,24 or 48 volts DC.
Rotor Diameter: 1.8m
Cut In Windspeed: 3 m/s (6.7 mph)

Rating: 72 W in a 11 m/s (24.6 mph) wind.
Voltage: 12 or 24 volts DC.
Rotor Diameter: 0.91m
Cut In Windspeed: 2.5 m/s (5.6 mph)

This 5m extension for Solar iBoost+ allows extension of the cable between the sender and the clamp sensor. This can be useful in properties with thick walls where moving the sender to the other side of a wall will help ensure good signal strength between the Solar iBoost+ and the sender.

These powerful tropicalised three-function PWM controllers provide reliable solar battery charging, load control or diversion regulation to divert excess power to a dump load for use in solar, wind or hydroelectric systems. (Two or more controllers may be used to provide multiple functions). Large heat sink enables operation at up to 45°C without de-rating. 3 LED's indicate battery status, alarms and faults. Optional LCD digital backlit display (included with -M version) provides system & controller information: battery voltage; current; temperature; amp-hours and error mode. Versions mount either on face of the controller or remotely. For use in either 12, 24 or 48V systems. Fully adjustable with DIP switches. RS232 communication for custom settings, data logging, remote monitoring/control. Reverse polarity, short circuit, over-current, high temperature and over-voltage protection. Operation from - 40 to+ 45°C. Terminals take up to 35sqmm cables.

These are the ideal controller for small professional and consumer systems. Fully encapsulated, they are approved for hazardous locations.

Morningstar’s PC MeterBus Adapter converts a controller’s MeterBus RJ-11 to a standard RS-232 serial connector for connection to a PC or other equipment. The MSC may be used with any Morningstar controller or inverter equipped with a meter connection that does not also already have a RS-232 port. Communications link enables monitoring and logging of data as well as customizing of set points.

SOL•THOR is a 0 to 3.6 kW linearly regulated DC Power Manager for photovoltaic heat. It takes power directly from a solar array and transfers it to a heating element, such as an immersion heater or space heater, without the need for a grid connection or external inverters.

The AC•THOR is a Photovoltaic-Power-Manager for hot-water and space-heating, providing linear control of electric heatsources depending on excess PV power and heat demand. It communicates via Ethernet with inverters, battery systems and smart home controllers and receives information on how much photovoltaic energy is available.

The AC•THOR 9s is a Photovoltaic-Power-Manager for hot-water and space-heating for use in 3-phase systems.

• Locking fit
  
• IEC 62852 DC voltage rating - 1000V
• IEC 62852 DC Current rating - 39A (4-6sqmm cable), 45A (10sqmm cable)
  

The MC4-Evo2 is latest version of the MC4 connector.

Stäubli MC4 branch connectors for parallel connections.

This enables small DC appliances such as chargers, radios & computer games etc. to be powered from a 12 or 24 V battery system with an output that can be switched to 12, 9, 7.5, 6, or 3 volts. Max output current is 1.5 A depending upon input & output voltages.

Remote graphical display for the Steca Solarix 2020-x2 solar charge controller. Energy flow is displayed as a graphic, making it intuitively understandable. Includes comprehensive data logger enabling full monitoring of the entire system. Virtually all charge controller parameters can be set and modified which allows the distribution of charge power between the two batteries to be adjusted. For the load output, all automatic time and battery voltage functions are fully programmable.

The programming unit Steca PA RC100 allows to program Steca solar charge controllers. The values can be adjusted with the help of switches. After a restart of the charge controller the new settings can be activated by pressing the program-button on the Steca PA RC100. An LED will transfer the values to the controller.

Varta Proffessional dual purpose EFB batteries are ideal for dual power applications where they can be used for both starting and overall energy supply.

Varta Proffessional dual purpose batteries are ideal for dual power applications where they can be used for both starting and overall energy supply.